|
TRIKO-PLEX®
Product
Data Guide
Triko-Plex
is an Architectural Grade Elastomeric Coating for Interior or Exterior Wall
Applications
• Excellent for Spray-On "Popcorn" Ceiling Effect
• Mold and Mildew Resistant
• VOC Compliant Waterborne Formulation
• Forms a Protective Weather Resistant Membrane
• Does NOT Contain Lead, Mercury or Asbestos
PRODUCT DESCRIPTION AND USE
Triko-Plex is an Architectural weatherproof
elastomeric coating specified for above grade applications to achieve a
superior decorative finish and weather-resistant protection for vertical
concrete, stucco, masonry and primed metal surfaces. Triko-Plex’s polymer
technology is a self-sealing liquid applied system that forms a seamless
weather resistant membrane to protect surfaces from the damaging effects of
rain, snow, wind, UV exposure, direct sunlight and heat. When properly
applied, Triko-Plex provides a long lasting, mildew resistant protective
coating for commercial, industrial and residential applications. Triko-Plex
is often specified for DOT projects, including bridges and median barriers.
Available in Smooth, Fine, Medium or Course finishes.
NOTE: NOT RECOMMENDED FOR
HORIZONTAL APPLICATIONS.
TYPICAL PHYSICAL PROPERTIES
Solids by Weight 61%
Solids by Volume 48%
Weight per Gallon 10.5 lbs.
Viscosity 104 KU’s
PH 9.2
Permeance 7.0 perms
Mildew Growth None
PACKAGING
TRIKO-PLEX is packaged and shipped in 5-gallon
pails and 55-gallon drums. An MSDS is shipped with each order and we
recommend that a set be kept available at the job site.
JOB CONDITIONS
Proceed
with application only when existing and forecasted weather conditions will
permit work to be performed in accordance with good construction practices.
This product is to be applied only to clean, dry sound surfaces. Do not
apply this product when the surface is wet or if ambient temperatures are
below 45° F or expected to drop below 45° F within a 24-hour period.
Triko-Plex is not recommended for below grade use or use on back filled
retaining walls. Do not apply during rain or if rain is expected within 24
hours after application.
Do not apply to horizontal surfaces where puddles or ponding water can
occur.
SURFACE PREPARATION
The surface must be properly prepared, cleaned and
repaired before any coating may be applied to avoid blistering, peeling or
delaminating and assure proper adhesion. Thoroughly clean the surface to
remove all dirt, loose granules, and contaminants (oil, grease, solvents,
etc.) that may interfere with proper adhesion. Pressure wash with a mix of
water, a biodegradable cleaner and bleach, scrub with a broom, thoroughly
rinse with clean water, and allow to completely dry. Thoroughly inspect and
test surface for any moisture before proceeding. The type and degree of
surface preparation will determine the success of the finished project.
Triko-Plex will not fill voids in substrates nor hide imperfections. Do not
apply directly to surfaces with a pH greater than pH 9.
HANDLING AND PREPARATION
Mix thoroughly for 5 to 10 minutes prior to
application at low speed to evenly disperse contents that may have settled
during shipping or storage. Rolling or shaking pails or drums will not
properly mix coating. DO NOT USE A DRUM HEATER or open flame or any other
source of open heat. DO NOT THIN. DO NOT ALLOW TRIKO-PLEX TO FREEZE. In hot
weather, opened containers may form a surface skin in the drum. This must be
removed before mixing or spraying so as not to gum up spraying equipment or
cause a lumping in the coating. All products have a shelf life. Do not open
or prepare a container until ready to apply. Use with adequate ventilation
and adhere to all applicable safety and equipment practices. Ground
electrical tools, machines and equipment in accordance with the National
Electrical Code.
COLOR
White. Custom colors and tints may be ordered with
minimum quantity requirements and will be quoted accordingly.
GRADE
Smooth. Also available in Fine, Medium and Course
textured finishes.
TYPICAL
COVERAGE RATES
Smooth - 100 sq. ft./gal. + 20
Fine - 65 sq. ft./gal. + 5
Medium - 45 sq. ft./gal. + 5
Coarse - 40 sq. ft./gal. + 5
Coverage rates are estimates only. Actual coverage
may vary depending upon the type, porosity and condition of the surface.
Test actual coverage for each project.
TYPICAL SHORT FORM SPECIFICATIONS
Inspect
surface, take photographs and detail job requirements for problem areas. Do
not apply coating until unsatisfactory conditions are repaired. Thoroughly
clean the surface to
remove all debris, dirt, flaking, loose granules, chalking and contaminants
(oil, grease, solvents, etc.) or anything else that may interfere with
proper adhesion. Concrete that is cracked or brittle must have protrusions,
cracks and splits repaired. Pressure wash with a mix of water, a
biodegradable cleaner and bleach, scrub with a broom, rinse with clean water
and allow to dry completely. The surface must be thoroughly inspected for
any moisture on or within the surface. Only apply Triko-Plex to clean, dry,
sound surfaces.
New Construction:
Concrete, stucco and masonry products must be
cured and free of excess moisture prior to the application of this coating.
Allow new concrete and stucco to cure 30 days and mortar joints to cure 15
days. Concrete or mortar with high lime content can cause excessive
alkalinity resulting in coating failure. Check the pH of the surface with an
Insta-Chek Surface pH Pencil or other measuring device. Surface alkalinity
is measured in pH with pH 7 being neutral. If the surface pH exceeds pH 9
(blue), treat the surface with a 5% muriatic acid and water solution, rinse
with clean water and let dry.
Concrete Block and Other Porous Surfaces
New or uncoated concrete block may require an
application of block filler prior to the application of the coating. Back
roll the base coat and first coat of the finish system to force out any
entrapped air and to increase adhesion.
Previously Coated Surfaces
Pressure wash the surface with hydro-spray
equipment (1500-2000 psi) using a maximum 25°
tip to remove all dirt, flaky paint or coating, mildew, chalk or other
foreign contaminants. Let it dry completely. If needed, apply a masonry
conditioner to tie down any chalking residue.
Surface repair:
Repair any cracks and surface imperfections using
the following guidelines prior to the application of the finish coats.
Hairline cracks
Triko-Plex weatherproof coating will bridge all
existing hairline cracks with no additional preparation necessary.
Small to medium cracks (less than 1/8")
Work an elastomeric filler into the crack with a
broad knife. Elastomeric fillers will remain flexible.
Medium to large cracks (1/8" to 1/4")
Work an
elastomeric filler into the crack with a broad knife. Allow it to dry. Apply
a second coat of filler if any shrinkage is evident. Apply another thin coat
over the prepared
crack and apply a single layer of reinforcing tape. Immediately after the
tape has adhered to the first coat, apply a second coat to smooth and embed
the tape. Feather the edges to ensure a uniform surface.
Surface imperfections
Can be patched by following the above procedures for medium to large cracks.
COATING APPLICATION
Triko-Plex Smooth coatings may be applied with a brush, roller or spray
equipment. Triko-Plex Fine, Medium and Coarse textures must be applied using
air-powered spray equipment only. Do not attempt to apply fine, medium or
coarse textures with a brush or roller. Use the product directly from the
container. Do not thin. Mix thoroughly with a power drill and mixing blade
prior to use. Apply Triko-Plex to properly prepared surfaces at the
recommended spread rate. Failure to apply the product at recommended rates
may result in poor performance or possible failure. Work the coating into
the surface for increased adhesion and to eliminate pinholes.
EQUIPMENT RECOMMENDATIONS
Triko-Plex Smooth
Spray application:
The following recommendations are the result of equipment manufacturers
testing and field experience. Contact the specific equipment manufacturer if
you are using equipment other than described here. 30:1 Graco President,
Senator, Bulldog, or King. Use 1/2" x 25’ max. or 3/8" x 50’ max. hose. Use
with .015-.025 Reverse-A-Clean tip. Airless/gas - Graco 433, 533 or 733 with
1/4" x 25’ max. or 3/8" x 50’ max. hose. Use with .015-.025 Reverse-A-Clean
tip.
Roller application
Use a roller with 3/4" to 1" nap. Wet the roller thoroughly with water and
spin it out before filling it with material. Apply liberally to the
specified wet mils. Roller application is not recommended for Medium or
Coarse finishes.
Brushing application
Use a 6 to 8 inch nylon bristle brush. Apply the product liberally to 2 to 3
sq. ft. areas at a time. Brush out the material to the specified wet mils,
using an interlock or fan stroke. Brushing should be reserved for the first
coat application on porous substrates only. Use a roller or spray
application for the second coat. Do not brush Medium or Coarse finishes.
Triko-Plex Fine, Medium, Coarse
Hand-held hopper gun
- select orifice and pressure to achieve desired texture appearance with
35-45 psi. Spray 18"-24" from surface. Air/bottom feed pot - 30’ max. of 1"
or 3/4" material hose and 1/2" air hose, double regular connected from tee,
Binks 7E2 gun with 1/4" orifice. Use ceramic or nylon insert for best
service. Set regulators at 50 psi material and 50 psi atomizing pressures.
Spray at 24" distance from surface.
LIMITED WARRANTY
The company warrants its product to be free of
manufacturing defects due to workmanship and materials for one year and in
accordance to the conditions stated in the individual product Technical
Data Sheets. This warranty is limited to the replacement of this product
when such product proves to be defective in manufacture. This express
warranty will only apply if the product is used for its specified
purposes. It does not apply to failures due to improper application.
The company shall not be liable, in any event,
for any incidental, consequential, special or indirect damages or damages
to a structure or its contents from any cause whatsoever. This warranty
may not be modified or amended by any employee, representative, agent or
customer of Lanco & Harris. This warranty is
exclusive and is in lieu of all other warranties, express or implied,
including any implied warranty of merchantability or fitness for a
particular purpose.
For more information, Contact:
|
