Ready Mix Aristex®

Product Data Guide

Aristex® is an Architectural Grade Coating for Interior Ceiling Applications

• Excellent for Spray-On "Popcorn" Ceiling Effect
• Mold and Mildew Resistant
• VOC Compliant Waterborne Formulation
• Forms a Protective Weather Resistant Membrane
• Does NOT Contain Lead, Mercury or Asbestos

PRODUCT DESCRIPTION AND USE

Aristex is an Architectural coating specified for above grade applications to achieve a superior decorative finish. Aristex polymer technology is a self-sealing liquid applied system that forms a seamless membrane to protect surfaces and provide a simulated acoustical decorative appearance. When properly applied, Aristex provides a long lasting, mildew resistant protective coating for commercial, industrial and residential ceiling applications. Available in Smooth, Fine, Medium or Course finishes.

TYPICAL PHYSICAL PROPERTIES

Solids by Weight 61%
Solids by Volume 48%
Weight per Gallon 10.5 lbs.
Viscosity 104 KU’s
PH 9.2
Permeance 7.0 perms
Mildew Growth None

PACKAGING                                                                                                                                       Back to Top

Aristex is packaged and shipped in 5-gallon pails and 55-gallon drums. An MSDS is shipped with each order and we recommend that a copy be kept available at the job site.

JOB CONDITIONS

Proceed with application only when conditions will permit work to be performed in accordance with good construction practices. This product is to be applied directly to clean, dry sound surfaces, both drywall and concrete. Do not apply this product when the surface is wet or if ambient temperatures are below 45° F or expected to drop below 45° F within a 24-hour period.

SURFACE PREPARATION

thoroughly rinse with clean water, and allow to completely dry. Thoroughly inspect and test concrete surfaces for any moisture before proceeding. The type and degree of surface preparation will determine the success of the finished project. Aristex will not fill voids in substrates nor hide imperfections. Do not apply directly to concrete surfaces with a pH greater than pH 9.

HANDLING AND PREPARATION

Mix thoroughly for 5 to 10 minutes prior to application at low speed to evenly disperse contents that may have settled during shipping or storage. Rolling or shaking pails or drums will not properly mix coating. DO NOT USE A DRUM HEATER or open flame or any other source of open heat. DO NOT THIN. DO NOT ALLOW ARISTEX TO FREEZE. In hot weather, opened containers may form a surface skin in the drum. This must be removed before mixing or spraying so as not to gum up spraying equipment or cause a lumping in the coating. All products have a shelf life. Do not open or prepare a container until ready to apply. Use with adequate ventilation and adhere to all applicable safety and equipment practices. Ground electrical tools, machines and equipment in accordance with the National Electrical Code.

 COLOR

White. Custom colors and tints may be ordered with minimum quantity requirements and will be quoted accordingly.

 GRADE

Available in Fine, Medium and Course textured finishes.

 TYPICAL COVERAGE RATES

Fine -         65 sq. ft./gal. + 5
Medium -  45 sq. ft./gal. + 5
Coarse -    40 sq. ft./gal. + 5

Coverage rates are estimates only. Actual coverage may vary depending upon the type, porosity and condition of the surface. Test actual coverage for each project.

TYPICAL SHORT FORM SPECIFICATIONS

Inspect surface, take photographs and detail job requirements for problem areas. Do not apply coating until unsatisfactory conditions are repaired. Thoroughly clean the surface to remove all debris, dirt, flaking, loose granules, chalking and contaminants (oil, grease, solvents, etc.) or anything else that may interfere with proper adhesion. Concrete that is cracked or brittle must have protrusions, cracks and splits repaired. Pressure wash concrete with a mix of water, a biodegradable cleaner and bleach, scrub with a broom, rinse with clean water and allow to dry completely. The surface must be thoroughly inspected for any moisture on or within the surface. Only apply Aristex to clean, dry, sound surfaces.

New Construction:

Concrete must be cured and free of excess moisture prior to the application of this coating. Allow new concrete and stucco to cure 30 days and mortar joints to cure 15 days. Concrete or mortar with high lime content can cause excessive alkalinity resulting in coating failure. Check the pH of the surface with an Insta-Chek Surface pH Pencil or other measuring device. Surface alkalinity is measured in pH with pH 7 being neutral. If the surface pH exceeds pH 9 (blue), treat the surface with a 5% muriatic acid and water solution, rinse with clean water and let dry.

Concrete Block and Other Porous Surfaces

New or uncoated concrete block may require an application of block filler prior to application. Back roll the base coat and first coat of the finish system to force out any entrapped air and to increase adhesion.

Previously Coated Surfaces 

Pressure wash the surface with hydro-spray equipment (1500-2000 psi) using a maximum 25° tip to remove all dirt, flaky paint or coating, mildew, chalk or other foreign contaminants. Let it dry completely. If needed, apply a masonry conditioner to tie down any chalking residue.                                                                                        Back to Top

Surface repair:

Repair any cracks and surface imperfections prior to application.

Hairline cracks

Aristex will bridge all existing hairline cracks with no additional preparation necessary.

Small to medium cracks (less than 1/8")

Work filler into the crack with a broad knife. There are elastomeric fillers that will remain flexible.

Medium to large cracks (1/8" to 1/4")

Work filler into the crack with a broad knife. Allow it to dry. Apply a second coat if any shrinkage is evident. Apply in a thin coat over the prepared crack and apply a single layer of Reinforcing Tape. Immediately after the tape has adhered to the first coat, apply a second coat to smooth to embed the tape. Feather the edges to ensure a uniform surface.

Surface imperfections

Can be patched by following the above procedures for medium to large cracks.

COATING APPLICATION

Aristex Fine, Medium and Coarse must be applied using air-powered spray equipment only. Do not attempt to apply fine, medium or coarse textures with a brush or roller. Use the product directly from the container. Do not thin. Mix thoroughly with a power drill and mixing blade prior to use. Apply to properly prepared surfaces at the recommended spread rate. Failure to apply the product at recommended rates may result in poor performance or possible failure. Backroll the coating into porous surfaces for increased adhesion and to eliminate pinholes.

EQUIPMENT RECOMMENDATIONS

Aristex Fine, Medium, Coarse

Hand-held hopper gun - select orifice and pressure to achieve desired texture appearance with 35-45 psi. Spray 18"-24" from surface. Air/bottom feed pot - 30’ max. of 1" or 3/4" material hose and 1/2" air hose, double regular connected from tee, Binks 7E2 gun with 1/4" orifice. Use ceramic or nylon insert for best service. Set regulators at 50 psi material and 50 psi atomizing pressures. Spray at 24" distance from surface.

LIMITED WARRANTY

The company warrants its product to be free of manufacturing defects due to workmanship and materials for one year and in accordance to the conditions stated in the individual product Technical Data Sheets. This warranty is limited to the replacement of this product when such product proves to be defective in manufacture. This express warranty will only apply if the product is used for its specified purposes. It does not apply to failures due to improper application.

The company shall not be liable, in any event, for any incidental, consequential, special or indirect damages or damages to a structure or its contents from any cause whatsoever. This warranty may not be modified or amended by any employee, representative, agent or customer of Lanco & Harris. This warranty is exclusive and is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose.

For more information, contact: